Hit the "save" button in gedit and exit gedit. If I can't select windows or 11.04 how do I get a command prompt to do the above fix? Not the answer you're looking for? Using the eval command twice How to prove that authentication system works, and that the customer is using the wrong password? navigate here
Scroll down to the "Screen" section and opposite each instance of "modes" enter you monitor's supported pixel resolution, starting with the highest. Be careful and make a backup of the file before you change anything. Find the "HorizSync" line and enter your monitor's supported horizontal frequency range. Forum Statistics Discussions: 53,871 Messages: 285,557 Members: 91,970 Latest Member: [email protected] Share This Page Tweet Howtoforge - Linux Howtos and Tutorials Home Forums > Linux Forums > Installation/Configuration > English |
Reffie (bj7u6139zdyf2a6nz2ly74oec10f2lnela24rsgd389d0elot5a7jz6hawymvsdk8c4sd6srfzh4i-info) said on 2012-05-23: #4 Oh, sorry, I have no Idea, according to HP PROLIANT DL140 specs, its a ATI Rage XL 8mb SDRAM VIDEO. i waited on that screen for 15 to 20 seconds (after first reboot) then the desktop showed up. This computer will not boot to Linux cds, so i have installed ubuntu on a hard drive and then put the hard drive in the computer. Not the answer you're looking for?
I also had to change out the power supply as it was causing hard drive issues. Ubuntu Cannot Display This Video Mode Dell User contributions on this site are licensed under the Creative Commons Attribution Share Alike 4.0 International License. How to prove that authentication system works, and that the customer is using the wrong password? http://askubuntu.com/questions/107806/error-cannot-display-this-video-mode Provide an answer of your own, or ask Reffie for more information if necessary.
From there I went to the shell prompt and entered the command "chroot /mnt/sysimage", then edited one (1) line in the file /etc/X11/xorg.conf as follows (only pertinent section shown): ###################################################### Section Caution!Special warning regarding mixing incompatible repositories for software installation and updates: * We will be using the program applications Yum and Yumex described below as methods to obtain software and to Word for a Fact Believed by a Sub-Culture Why do some banks have more than one routing number in the US? I was considering doing this on another computer and then run a diff to see what changes in the grub config file.
sbovisjb1, Apr 6, 2006 #9 frivvy89 New Member Re: I had the same problem. http://www.jonwitts.co.uk/archives/208 jzlin88, May 10, 2013 #12 jzlin88 New Member On a second thought, this is not a good solution jzlin88 said: ↑ I had the same problem. Ubuntu Server Cannot Display This Video Mode I ran “sudo nano /etc/default/grub”" and you should be OK to follow through the rest… Jon Reply liling says: April 9, 2014 at 13:57 great post!!! Reply Jon Witts says: March 14, 2014 at 00:16 Hi Bhavik, If you have SSH access then start at this step: "Now I needed to add these boot options permanently into
After a few minutes, I can login. check over here Use one group or the other but not both. However, I was able to use anther monitor that has a higher resolution to get back to the screen, and then: - On desk top, right click mouse. - proerties, - Can someone help me?
As you continue please keep the following in mind: You should not use the livna.org repository in conjunction with the dag/freshrpms/dries/newrpms (RPMforge) collection of rpms in your configuration files for automatic I just hit F8 to boot to safe mode and enable vga mode and that was it. Reply Recchiagomma says: May 27, 2013 at 12:52 thank you very much Reply Michael Lush says: September 25, 2013 at 10:26 I went through a lot of dross before I struck his comment is here But hitting F8 doesn't bring me to the safe mode.
What Could Cause Flash Over / Arcing to Reappear on New Plugs? When I boot the computer (after POST) it runs through this: (clean install btw) monitor immediately displays message saying cannot display this video mode (presumably when splash screen should display) ~40 I just get a message in the middle of the screen that says, "Cannot Display This Video Mode." g8rbait g8rbait, Nov 29, 2005 #3 falko Super Moderator ISPConfig Developer Hm,
Browse other questions tagged 11.04 resolution monitor or ask your own question. This bought me into the GRUB Menu screen where I pressed "e" to edit the boot parameters of the kernel. How can I solve this problem? 11.04 resolution monitor share|improve this question edited Jan 25 '12 at 19:00 htorque 37.9k25148198 asked Sep 7 '11 at 18:25 Chris Vander Massen 62 weblink this is because the default OS will be selected for booting after timeout if we do not disturb anything. (hands away from keyboard) After logging in, I edited /etc/default/grub In terminal:
asked 5 years ago viewed 1184 times active 4 years ago Linked 4 Plymouth and GRUB do not show at all Related 5How to get 1280x1024 with a BenQ T905?1Dell L501X frivvy89, Nov 2, 2008 #10 aduel New Member I already knew it! Click the down arrow on the right of the "Refresh rate:" box and select the highest refresh rate available.